CurveFilletSurfaceToRail Method

public bool FilletSurfaceToRail(
	BrepFace faceWithCurve,
	BrepFace secondFace,
	double u1,
	double v1,
	int railDegree,
	int arcDegree,
	IEnumerable<double> arcSliders,
	int numBezierSrfs,
	bool extend,
	FilletSurfaceSplitType split_type,
	double tolerance,
	List<Brep> out_fillets,
	List<Brep> out_breps0,
	List<Brep> out_breps1,
	out double[] fitResults
)

Public Function FilletSurfaceToRail ( 
	faceWithCurve As BrepFace,
	secondFace As BrepFace,
	u1 As Double,
	v1 As Double,
	railDegree As Integer,
	arcDegree As Integer,
	arcSliders As IEnumerable(Of Double),
	numBezierSrfs As Integer,
	extend As Boolean,
	split_type As FilletSurfaceSplitType,
	tolerance As Double,
	out_fillets As List(Of Brep),
	out_breps0 As List(Of Brep),
	out_breps1 As List(Of Brep),
	<OutAttribute> ByRef fitResults As Double()
) As Boolean

Parameters

faceWithCurve

Type: Rhino.GeometryBrepFace
The first face on which the curve exists

secondFace

Type: Rhino.GeometryBrepFace
The second face

u1

Type: SystemDouble
A parameter in the u direction of the second face at the side you want to keep after filleting.

v1

Type: SystemDouble
A parameter in the v direction of the second face at the side you want to keep after filleting.

railDegree

Type: SystemInt32
Desired fillet degree (3 or 5) in the u-direction, along the rails

arcDegree

Type: SystemInt32
esired fillet degree (2, 3, 4, or 5) in the v-direction, along the fillet arcs.If 2, then the surface is rational in v

arcSliders

Type: System.Collections.GenericIEnumerableDouble
Array of 2 sliders to shape the fillet in the arc direction, used for arcDegree = 3, 4, or 5; input { 0.0, 0.0 } to ignore [0] (-1 to 1) slides tangent arms from base (-1) to theoretical(1) [1] (-1 to 1) slides inner CV(s) from base (-1) to theoretical(1)

numBezierSrfs

Type: SystemInt32
If >0, this indicates the number of equally-spaced fillet surfaces to be output in the rail direction, each surface Bézier in u.

extend

Type: SystemBoolean
If true, then when one input surface is longer than the other, the fillet surface is extended to the input surface edges.

split_type

Type: Rhino.GeometryFilletSurfaceSplitType
The split type

tolerance

Type: SystemDouble
The tolerance. In in doubt, the the document's absolute tolerance.

out_fillets

Type: System.Collections.GenericListBrep
The results of the fillet calculation.

out_breps0

Type: System.Collections.GenericListBrep
The trim or split results of the Brep owned by faceWithCurve.

out_breps1

Type: System.Collections.GenericListBrep
The trim or split results of the Brep owned by pFace1.

fitResults

Type: SystemDouble
array of doubles indicating fitting results: [0] max 3d point deviation along surface 0 [1] max 3d point deviation along surface 1 [2] max angle deviation along surface 0 (in degrees) [3] max angle deviation along surface 1 (in degrees) [4] max angle deviation between Bézier surfaces(in degrees) [5] max curvature difference between Bézier surfaces

Return Value

Reference