MeshingParameters
=================

.. py:module:: rhino3dm

.. py:class:: MeshingParameters

   .. py:method:: MeshingParameters()

      MeshingParameters constructor


   .. py:method:: MeshingParameters(density)

      Initializes a new instance with simple values,
      similar to that of Rhino's meshing slider interface.

      :param float density: The density and number of mesh polygons, where 0.0 <= density <= 1.0, \
         where 0 quickly creates coarse meshes, and 1 slowly creates dense meshes.

   .. py:method:: MeshingParameters(density, minimumEdgeLength)

      Initializes a new instance with simple values,
      similar to that of Rhino's meshing slider interface.

      :param float density: The density and number of mesh polygons, where 0.0 <= density <= 1.0, \
         where 0 quickly creates coarse meshes, and 1 slowly creates dense meshes.
      :param float minimumEdgeLength: The minimum allowed mesh edge length.

   .. py:attribute:: Default

      rhino3dm.MeshingParameters: Gets mesh creation parameters to create the default render mesh.
      Only use this if you plan on specifying your own custom meshing
      parameters.

   .. py:attribute:: FastRenderMesh

      rhino3dm.MeshingParameters: Gets mesh creation parameters to create the a render mesh when
      meshing speed is preferred over mesh quality.

   .. py:attribute:: QualityRenderMesh

      rhino3dm.MeshingParameters: Gets mesh creation parameters to create the a render mesh when mesh
      quality is preferred over meshing speed.

   .. py:attribute:: DefaultAnalysisMesh

      rhino3dm.MeshingParameters: Gets mesh creation parameters to create the default analysis mesh.

   .. py:attribute:: TextureRange

      MeshingParameterTextureRange: Gets or sets how and if textures will be packed.

   .. py:attribute:: JaggedSeams

      bool: Gets or sets whether or not the mesh is allowed to have jagged seams.
      When this flag is set to true, meshes on either side of a Brep Edge will not match up.

   .. py:attribute:: RefineGrid

      bool: Gets or sets a value indicating whether or not the sampling grid can be refined
      when certain tolerances are not met.

   .. py:attribute:: SimplePlanes

      bool: Gets or sets a value indicating whether or not planar areas are allowed
      to be meshed in a simplified manner.

   .. py:attribute:: ComputeCurvature

      bool: Gets or sets a value indicating whether or not surface curvature
      data will be embedded in the mesh.

   .. py:attribute:: ClosedObjectPostProcess

      bool: Gets or sets a value indicating whether or not to post process non-closed meshes
      that should be closed. If the Brep being meshed is closed, JaggedSeams = false,
      and ClosedObjectPostProcess = true, and the resulting mesh is not closed, then a
      post meshing process is applied to find and close gaps in the mesh. Typically the
      resulting mesh is not closed because the input Brep has a geometric flaw, like
      loops in trimming curve.

   .. py:attribute:: GridMinCount

      int: Gets or sets the minimum number of grid quads in the initial sampling grid.

   .. py:attribute:: GridMaxCount

      int: Gets or sets the maximum number of grid quads in the initial sampling grid.

   .. py:attribute:: GridAngle

      float: Gets or sets the maximum allowed angle difference (in radians)
      for a single sampling quad. The angle pertains to the surface normals.

   .. py:attribute:: GridAspectRatio

      float: Gets or sets the maximum allowed aspect ratio of sampling quads.

   .. py:attribute:: GridAmplification

      float: Gets or sets the grid amplification factor.
      Values lower than 1.0 will decrease the number of initial quads,
      values higher than 1.0 will increase the number of initial quads.

   .. py:attribute:: Tolerance

      float: Gets or sets the maximum allowed edge deviation.
      This tolerance is measured between the center of the mesh edge and the surface.

   .. py:attribute:: MinimumTolerance

      float: Gets or sets the minimum tolerance.

   .. py:attribute:: RelativeTolerance

      float: Gets or sets the relative tolerance.

   .. py:attribute:: MinimumEdgeLength

      float: Gets or sets the minimum allowed mesh edge length.

   .. py:attribute:: MaximumEdgeLength

      float: Gets or sets the maximum allowed mesh edge length.

   .. py:attribute:: RefineAngle

      float: Gets or sets the mesh parameter refine angle in radians.

   .. py:method:: Encode()

      [todo] add documentation

   .. py:staticmethod:: Decode(jsonObject)

      [todo] add documentation